Mikado Logo 690 SX User Manual download pdf (Page 2)

Manual LOGO 690SX - ©Mikado Model Helicopters GmbH - Page 2

Index

OPERATING YOUR MODEL SAFELY

Operate the helicopter in spacious areas with no

people nearby.

!Warning: Do NOT operate the helicopter in the fol-

lowing places and situations (or else you risk severe

accidents):

• in places where children gather or people pass

through

• in residential areas and parks

• indoors and in limited space

• in windy weather or when there is any rain, snow,

fog or other precipitation

If you do not observe these instructions you may be

held reliable for personal injury or property damage!

Always check the R/C system prior to operating your

helicopter. When the R/C system batteries get weaker,

the operational range of the R/C system decreases.

Note that you may lose control of your model when

operating it under such conditions.

Keep in mind that other people around you might also

be operating a R/C model.

Never use a frequency which someone else is using

at the same time. Radio signals will be mixed and you

will lose control of your model.

If the model shows irregular behavior, bring the model

to a halt immediately. Turn off all power switches and

disconnect the batteries. Investigate the reason and

x the problem. Do not operate the model again as

long as the problem is not solved, as this may lead to

further trouble and unforeseen accidents.

! Warning: In order to prevent accidents and personal

injury, be sure to observe the following:

Before ying the helicopter, ensure that all screws are

tightened. A single loose screw may cause a major

accident.

Replace all broken or defective parts with new ones,

as damaged parts lead to crashes.

Never approach a spinning rotor. Keep at least 10 me-

ters/yards away from a spinning rotor blades.

Do not touch the motor immediately after use. It may

be hot enough to cause burns.

Perform all necessary maintenance.

PRIOR TO ADJUSTING AND OPERATING YOUR MO-

DEL, OBSERVE THE FOLLOWING

!Warning: Operate the helicopter only outdoors and

out of people’s reach as the main rotor operates at

high rpm!

! Warning: While adjusting, stand at least 10 meters/

yards away from the helicopter!

Novice R/C helicopter pilots should always seek advice

from experienced pilots to obtain hints with assem-

bly and for pre-ight adjustments. Note that a badly

assembled or insufciently adjusted helicopter is a

safety hazard!

In the beginning, novice R/C helicopter pilots should

always be assisted by an experienced pilot and never

y alone!

Tools for Assembly & R/C Equipment

Radio with Heli-Software

Motor + Speed Controller (check the Mika-

do webpages for recommended motors)

Alle shown products are examples. You may use different brands.

Scissors

Rubber Hammer

Screwdrivers

(plus and minus)

Hex Wrenches

1.5/2.0/2.5/3.0/4.0 mm

(.055/.079/.098/.118 in)

Ball

link

pliers

Threadlock

circlips

pliers

Grease

Pitch Gauge

Safety Instructions

Safety Instructions . . . . . . . . . . . . . . . . . 2

Tools for Assembly & R/C Equipment . . . . . . . 2

1 Mainframe . . . . . . . . . . . . . . . . . . . . . 3

2 Tail Rotor . . . . . . . . . . . . . . . . . . . . . 4

3 Tail Boom . . . . . . . . . . . . . . . . . . . . . 5

4 Main Gear & Tail Boom Assembly . . . . . . . . 6

5 V-Bar Rotor Head . . . . . . . . . . . . . . . . . 7

6 Servo Installation . . . . . . . . . . . . . . . . . 8

7 Mounting the Motor . . . . . . . . . . . . . . . . 9

8 Canopy Mounting . . . . . . . . . . . . . . . . . 9

9 Radio and Battery . . . . . . . . . . . . . . . 10

10 Overview Chassis . . . . . . . . . . . . . . . 11

11 Overview Tail Rotor . . . . . . . . . . . . . . 12

12 Overview V-Bar Head . . . . . . . . . . . . . 13

V-Bar

Manual Mikado LOGO 690 SX

Note: There is no bag 10. The bags are numbered 1 to 12, with the exception of 10.

Max. rotorhead rpm LOGO SX 690: 2000

Max. collective range: +/- 11°

Max. rotor blade size: 690 mm

Max. tail rotor blade size: 105mm

Max. LiPo Akku size: 10S 5000 mAh

Max. LiPo Akku size: 12S 5000 mAh

LOGO 690 SX is not recommended for novices. This heli-

copter is a complex system. Basic knowledge of the func-

tion of a model helicopter is required to build and operate

the LOGO 690 SX.

Minute

Epoxy

Minute

Epoxy

Warning:

The LOGO 690 SX is designed to be used with Scorpion motor HK 4525-370 Kv and a 15 teeth pinion exclu-

sively. Do not use any other motors of any kind, as this can cause damage or failure of the gear train. It is

absolutely essential to keep within the recommended pitch range from +/- 11°. Otherwise the one way bearing

will be damaged.

1 2 3 4 5 6 7 ... 12 13

Comments to this Manuals

No comments

Mikado Logo 690 SX User Manual Page 2

Comments to this Manuals

Related products and manuals for Toys & accessories Mikado Logo 690 SX