Mikado Logo 600 Specifications download pdf (Page 2)

Additional precautions for the prevention of injuries or damage:

Before you power on the helicopter, you must ensure that all screws and associated hardware are secured. One

single lose screw can cause the helicopter to become uncontrollable resulting in a crash or injury to personnel.

Also it is very important that you must check the model frequently and exchange any parts that show signs of

deterioration or wear.wearing out. Failure to complete frequent pre and post ight inspections will result in ying an

unsafe model and increasing the risk of damaging the helicopter and possibly injuring yourself and/or others. Use

only original Mikado parts and electronic components which are recommended by Mikado.

Always keep a minimum of 10 yards away from a spinning rotor head. Components that run hot such as the ESC

and Motor should never be touched until ample cool down time has been provided.

Before powering on the helicopter:

Never operate the helicopter inside closed rooms as this helicopter is intended for operation outside and may only

be operated in sites where operation of Radio Control models is permitted. . Keep the helicopter at safe distance to

any persons or live animals at all times. When trimming, keep a minimum distance of 10 yards for safety and never

operate the helicopter alone. Always take someone with you, who can help in emergency situations.

The helicopter must also not be operated in the following circumstances:

• when children are present or in places where people are gathering

• close to houses or in park areas

• inside any rooms or buildings

• places with limited space

• in adverse weather conditions, such as rain, snow, hail or during strong winds

• Near trees or High Tension wires

Techical specications which must be obeyed during the operation of the

LOGO 700 XXtreme:

• maximum rotor head rpm: 2100 U/min.

• maximum pitch travel: +/- 12°

• Length of rotor blades: 700 to 750mm

• Lipo battery: 2x 6S 5000 mAh

• admissible temperature 0° - 35° Celsius

If these values are exceeded, the electronic components may experience overload. This may result in damage or a

crash of the helicopter.

Before the rst ight, you must check proper functioning of the motor, the ESC and the VBar. To do this, please refer

to the respective manuals. For safety reasons, these tests should be performed without mounting the main rotor

blades and the tail rotor blades. It is advisable to y moderately during the rst ights. This is because you need to

get used to the new size of this helicopter during the rst few ights. Do not underestimate the size and power of

this helicopter. Keep a safe distance from the ground to provide for ample reaction time.

Index

Safety Instructions/ Tools for Assembly & RC Equipment 2

1 Mainframe 3

2 Servo Mounting 4

3 Main Gear 5

4 Landing Struts and Canopy Holder 6

5 Motor Installation 7

6 Tail Rotor 8

7 Torque Tube 9

8 Tail Boom Mounting 10

9 Tail Boom Brace 11

10 Swashplate 12

11 Rotor Head 13

12 Wiring RC Components 15

13 Mounting ESC and Voltage Regulator 16

14 Battery Mounting 17

15 Main Rotor Blades and Tail Rotor Blades 18

16 Canopy and Overview 19

17 Overview Spare Parts Mainframe 20

18 Overview Spare Parts Gear Box 22

19 Overview Spare Parts Tail Boom 23

20 Overview Spare Parts Tail Rotor 24

21 Overview Spare Parts Rotor Head 25

Thank you very much for your purchase of the Mikado LOGO 700 XXtreme. Prior to installation, please read and

understand this manual completely and follow all instructions exactly. If any instructions are not clear to you or if you

have any questions, you must contact us. You can reach Mikado on the LOGO-Forum on www.vstabi.info or contact

the Mikado support hotline via email or phone. Do not under any circumstances y this helicopter if you are unsure

of setup or assembly.

This helicopter is not suitable for beginners. It is expected that you have some experience in assembling and

operating an RC helicopter (model size LOGO 400 to LOGO 600, for example). You are required to adhere to the

safety instructions of this manual.

The LOGO 700 XXtreme comes partially pre-assembled, i.e. the structural components are already screwed together.

However, the screws are not yet secured with Loctite. Throughout the manual you will not always be asked to secure

each screw. Nevertheless, you must secure all screws in all components yourself. In addition, it is necessary that

you secure all other screwed connection, by which you will assemble the different components of the LOGO 700

XXtreme. We recommended to use securing glue Loctite 243 (blue). Please follow the recommendations of the

Loctite manufacture and allow proper curing time for the Loctite prior to ying the model.

Safety Instructions:

RC Helicopters are not toys and must be treated with due diligence. Unless you use this helicopter responsibly it

can cause of severe injury and immense damage. Inappropriate use of this product can result in injury or death.

Each user must have the appropriate knowledge and skill to operate any RC Helicopter. Manufacturer / reseller

assumes no liability for the use or operation of this helicopter.

You are responsible for any injury and damage that may be caused by this helicopter. It is recommended that your

radio components be tested prior to installing in this helicopter. Improper radio installation or inadequate battery

voltage can result in the loss of control of the helicopter. Proper knowledge of your radio equipment is required prior

to ying this helicopter. You must check if other persons are using an RC-controlled model or device simultaneously,

as this may result in interference. If the helicopter behaves in an unusual or strange way, you must land it immediately

and turn off the power. Please meticulously check all of your radio gear and nd/x the problem before you continue

to operate the helicopter This is to avoid any accidents. As one irregularity can cause other defects or problems, an

increased risk of failure will ensue, if the rst problem is not xed.

Hex Wrenches

1,5/2,0/2,5/3,0/4,0/6,0 mm

needle

nose

pliers

Page 2

1 2 3 4 5 6 7 ... 24 25

Comments to this Manuals

No comments

Mikado Logo 600 Specifications Page 2

Comments to this Manuals

Related products and manuals for Toys & accessories Mikado Logo 600